Monostatic microwave sensors “Forteza M-60" and "Forteza M-30" volume,curtain,fan.

---

1.Purpose

1.1. The purpose of “FORTEZA-M60” and "Forteza-M30" is to protect perimeter sites, outside (inside) grounds of different objects and to detect an intruder moving in his full height or bent in a detection zone.
1.2 The sensor is intended for continuous outdoor round-the-clock operation. It keeps operating at the ambient temperature -50°…+50°С and relative humidity up to 98% at the temperature +35°С.
1.3. The distinctive feature of the sensor is the detection zone generation consisting of 12 cross-cut sub bands. They permit to control its operation by PC over USB - interface (cross-cut sub bands disconnection, separated sensitivity’s adjustment in every cross-cut sub band, etc).

2.Specifications

2.1. The maximum length of a Forteza M-60 detection zone is 60 m maximum (12 cross-cut sub bands for 5 m) for Forteza M-30 detection zone is 30 m maximum (12 cross-cut sub bands for 2.5 m). The detection zone is a volumetric part of the perimeter site and any intruder’s movement in which generates an alarm. The characteristics of the detection zone for different performance variants are given in table 1.1.

Table 1.1.

FORTEZA M-60 Characteristics

FORTEZA M-30 Characteristics

2.2. The sensor provides the adjustment of the length from 5 m to 60 m.
2.3. The sensor generates an alarm when:

• an intruder (to his full height or bowed) crosses the detection zone  at a speed of 0,3...8 m/sec;
• the signal injection of the  remote control;
• dump or supply voltage reduction up to 4.2 ±0,4 V;
• sabotage attempt by the radiation screening with radio reflecting or radio absorptive materials  at the distance up to 2 m (anti masking function).

An alarm is generated by breaking the contacts of an individual point relay of 3 sec minimum. This signal is issued with the yellow and pink colored marked cables.

2.4. The characteristics of the individual optoelectronic point relay: switching current is 0,1 A maximum; the maximum voltage is 50 V. The resistance in the closed condition is 130 Ohm max (with the lightning guard elements).
2.5. The sensor generates a tamper alarm where the control devices are situated. Then the contacts of the tamper circuit are broken. This signal is issued by the blue and grey colored marked cables. Contact dimensions of this tamper circuit are: current up to 0,2A at voltage up to 80 VDC.
2.6. The recovery time of a standby state after an alarm is 1 sec maximum.
2.7. The time of the technical availability after the supply voltage signal is 5 sec maximum.
2.8. The sensors are supplied from the direct current of 6...30 V and pulsation 0,03 V maximum.
The sensor’s power is 0,6 Watt maximum.
2.9. The sensor has the automatic and remote control of the availability.
To operate with the remote control, dc voltage of 6…30 V with the duration of 1 sec is given on the green colored cable. In this case the sensor must generate an alarm.
2.10. The sensor doesn’t generate an alarm when:

• rain, snow, fog;
• solar radiation;
• the influence of wind at  a  speed of  20m/sec. maximum;
• movement of the birds and animals with the linear sizes of 0,3 m max;
• the height of irregularities on the perimeter site up to + 0,3 m;
• the height of snow up to 0,3m without additional adjustment;
• the height of grass up to 0,2 m;
• the influence of the ultra-short waves  433 MHz and  the mobile phone at the distance more than 0,5 m from the sensor.

2.11. The sensor is immune to EMI (voltage impulses in supply circuits, breaks of mains supply, electrostatic discharges, electromagnetic fields).
2.12. Input circuits of the sensor are protected from electric pickup (electric storm too).
2.13. The sensor mean lifetime is 8 years.
2.14. The overall dimensions of the sensor without the mounting kit (MK) are 210х135х55 mm maximum;
2.15. Maximum weight of the units with a mounting kit, kg: 0.5

Option "fan" (red - under the protection, green - is disarmed)	Option "blind" (red - under the protection, green - is disarmed)